Best Concrete Basketball Court Contractors Garner NC

Basketball exposes concrete flaws that ordinary use never would. The dribble demands a finish smooth enough for consistent bounce yet textured enough that a hard cut grips instead of slides — a narrow band we finish to deliberately. The goal post gets an isolated footing so a rattled dunk attempt doesn't ring vibration through the playing slab, and the court goes down as a single-plane pour, because a cold joint at midcourt is a future crack with a painted line running through it. On Garner lots we settle placement before anything else, weighing sun angle, ball containment, and the neighbors' windows, then commit the concrete.

In Garner specifically, basketball court work runs through neighborhoods like Heather Hills, Turner Farms, Heather Woods. The clay under south Garner holds water on the flatter lots near Lake Benson, so slab drainage and base prep decide how long a new pour lasts. That local ground truth — not a generic spec sheet — is what the crew builds against when they form up a Garner court pour.

Basketball Court Slab Sizes and Specs We Pour

Court size is a mix of what you want to play and what actually fits in the yard. Getting the slab spec right for the size and use pattern makes the difference between a court that plays like a real court and one that spider-cracks by year three.

• Hoop pad — 30×30 (900 SF), room for a hoop plus a solid free-throw shooting area and enough space to move for one-on-one
• Backyard half court — 30×50 (1,500 SF), enough for a painted key, three-point line, and adult-scale play
• Regulation-style half court — 50×47 (2,350 SF), full NBA half-court dimensions with three-point arc, key, and full baseline run
• Small full court — 50×74 (3,700 SF), high-school-style shortened full court
• Regulation full court — 50×94 (4,700 SF), NBA/college full dimensions, typically HOA or club scope
• Driveway-conversion court — existing driveway extended or repoured to hit court dimensions
• Multi-sport pad — basketball plus pickleball line overlay on 30×60 or 34×64

Every slab we pour hits the same core spec: 5-inch minimum thickness (6 inches on courts with in-ground hoop bases embedded through the slab), 4,000 psi mix, #4 rebar on 16-inch centers, sawcut control joints on a 12×12 grid, 1% slope in one direction for drainage (side-to-side is standard, never toward the hoop-side sideline), broom or steel-trowel-then-broom finish depending on the surfacing plan, and cast-in-place hoop footings poured before or with the slab pour.

Base Prep, Drainage, and Why Most Courts Crack Early

The single biggest reason a basketball court fails early is the base underneath the slab. A pad poured directly on unimproved subgrade or on 2 inches of loose stone will telegraph settlement cracks within a year, and the point-load of a heavy in-ground hoop base makes the failure worse — the slab sinks unevenly under the hoop before it does anywhere else.

Our base spec: strip 8-10 inches of topsoil, compact the subgrade to 95% Proctor, install and grade 4-6 inches of #57 washed stone as a drainage layer, compact again in 2-inch lifts, then pour on top. Under the hoop location specifically we go deeper on the stone base (6-8 inches) because a full-size in-ground hoop with a 4×4×48-inch anchor footing puts serious localized load on that spot every time the rim gets used.

Drainage direction matters. The slab must fall 1% (about 1 inch of drop over 8 feet) in one direction so water sheds off the pad. Sloping toward the hoop creates a puddle right where you shoot free throws every time it rains, and a dead-flat court holds water at the low spots and shortens surface life. Perimeter drainage — a French drain along the low side, or at minimum a graded swale directing water 10 feet clear of the pad — keeps the base dry season after season.