Best Concrete Basketball Court Contractors Clemmons NC

The requirements only reveal themselves mid-game. Dribble a ball across ordinary broom finish and it skips oddly; sprint a defensive slide on slick trowel work and you are on the ground — so court texture lives in a narrow band we finish for deliberately. The goal post gets its own isolated footing, decoupled from the slab, so a hard dunk attempt sends vibration into the earth rather than through the concrete. And we pour the playing surface in one continuous placement whenever access allows, because a cold joint across the key eventually becomes a crack across the key. Clemmons families with the yard for it get a court that plays as good as it looks.

In Clemmons specifically, basketball court work runs through neighborhoods like Tanglewood Forest, Cobblestone, Wyngrove. Clemmons West alone spans construction from the mid-1970s through 2014, so the concrete work here splits by street. That local ground truth — not a generic spec sheet — is what the crew builds against when they form up a Clemmons court pour.

Basketball Court Slab Sizes and Specs We Pour

Court size is a mix of what you want to play and what actually fits in the yard. Getting the slab spec right for the size and use pattern makes the difference between a court that plays like a real court and one that spider-cracks by year three.

• Hoop pad — 30×30 (900 SF), room for a hoop plus a solid free-throw shooting area and enough space to move for one-on-one
• Backyard half court — 30×50 (1,500 SF), enough for a painted key, three-point line, and adult-scale play
• Regulation-style half court — 50×47 (2,350 SF), full NBA half-court dimensions with three-point arc, key, and full baseline run
• Small full court — 50×74 (3,700 SF), high-school-style shortened full court
• Regulation full court — 50×94 (4,700 SF), NBA/college full dimensions, typically HOA or club scope
• Driveway-conversion court — existing driveway extended or repoured to hit court dimensions
• Multi-sport pad — basketball plus pickleball line overlay on 30×60 or 34×64

Every slab we pour hits the same core spec: 5-inch minimum thickness (6 inches on courts with in-ground hoop bases embedded through the slab), 4,000 psi mix, #4 rebar on 16-inch centers, sawcut control joints on a 12×12 grid, 1% slope in one direction for drainage (side-to-side is standard, never toward the hoop-side sideline), broom or steel-trowel-then-broom finish depending on the surfacing plan, and cast-in-place hoop footings poured before or with the slab pour.

Base Prep, Drainage, and Why Most Courts Crack Early

The single biggest reason a basketball court fails early is the base underneath the slab. A pad poured directly on unimproved subgrade or on 2 inches of loose stone will telegraph settlement cracks within a year, and the point-load of a heavy in-ground hoop base makes the failure worse — the slab sinks unevenly under the hoop before it does anywhere else.

Our base spec: strip 8-10 inches of topsoil, compact the subgrade to 95% Proctor, install and grade 4-6 inches of #57 washed stone as a drainage layer, compact again in 2-inch lifts, then pour on top. Under the hoop location specifically we go deeper on the stone base (6-8 inches) because a full-size in-ground hoop with a 4×4×48-inch anchor footing puts serious localized load on that spot every time the rim gets used.

Drainage direction matters. The slab must fall 1% (about 1 inch of drop over 8 feet) in one direction so water sheds off the pad. Sloping toward the hoop creates a puddle right where you shoot free throws every time it rains, and a dead-flat court holds water at the low spots and shortens surface life. Perimeter drainage — a French drain along the low side, or at minimum a graded swale directing water 10 feet clear of the pad — keeps the base dry season after season.