Concrete Pickleball Court Installer in Charlotte, NC

A pickleball court is one of the more forgiving concrete slabs to pour on paper — flat, rectangular, no vehicle load, no freeze-thaw abuse if the surfacing goes on right — but almost every court failure we see traces back to the same handful of shortcuts: undersized pad, wrong slope, no isolation between the slab and the fence footings, mesh instead of rebar, or a base that was never compacted to a real standard. A regulation playing area is 20 feet by 44 feet, but the pad you actually want to pour is 30×60 (1,800 SF minimum) with 34×64 preferred for tournament-comfortable run-back and side buffers. The extra concrete is cheap relative to the total build, and it decides whether the court plays like a real court or feels cramped from day one.

Local Concrete Contractor scopes pickleball courts across North Carolina starting with a site walk covering pad orientation (north-south long axis to keep sun out of the servers' eyes), grade and drainage, subgrade type, tree and root proximity, access for the pour truck, and how the court will be finished after the slab cures — acrylic color coat by a court-surfacing crew is the standard next step. We deliver a written spec covering pad dimensions, slope, base build, thickness, reinforcement, joint pattern, mix design, net-post sleeves, fence-post isolation, and finish before any dirt moves. No deposit up front, no vague scope on the invoice, and no marketing gloss on the spec sheet.

Pickleball Court Slab Specs We Pour

Court quality lives or dies on the slab underneath the acrylic. Getting the size, slope, thickness, and reinforcement right makes the surfacing coat last 8-12 years instead of failing in 3.

• Standard residential court — 30×60 pad (1,800 SF), 20×44 playing area with 5-ft side buffers and 8-ft baseline run-back
• Tournament-comfortable court — 34×64 pad (2,176 SF), 7-ft side and 10-ft baseline buffers
• Two-court side-by-side — 60×64 pad (3,840 SF) with 10-ft center separation
• Multi-sport pad — pickleball lines plus basketball key overlay, typically 30×60 to 40×70 depending on hoop configuration
• Driveway-conversion court — existing driveway extended or repoured to hit court dimensions
• HOA and church rec courts — 30×60 or 34×64 with additional post sleeves for 4-court fence sections

Every slab we pour hits the same core spec: 4-inch minimum thickness (5-inch on any court with fence posts embedded through the pad), 4,000 psi mix, #4 rebar on 16-inch centers or wire fabric mat as a written second choice, sawcut control joints on a 12×12 grid, 1% side-to-side slope (never net-to-net), and cast-in-place net-post sleeves so the surfacing coat can wrap the sleeve without cracking.

Base Prep, Drainage, and Why Most Courts Crack Early

The single biggest reason pickleball courts fail early is the base underneath. A pad poured directly on unimproved subgrade or on 2 inches of loose stone will telegraph settlement cracks within a year, and once those cracks reach the acrylic surface the whole court has to be resurfaced.

Our base spec: strip 8-10 inches of topsoil, compact the subgrade to 95% Proctor, install and grade 4-6 inches of #57 washed stone as a drainage layer, compact again in 2-inch lifts, then pour on top. The stone base does two jobs — it distributes point loads from any future fence footings and gives water somewhere to go instead of sitting under the slab through winter.

Drainage direction matters more than most owners realize. The slab must fall 1% (about 1 inch of drop over 8 feet) side-to-side, never net-to-net. Sloping toward the net creates a puddle across the whole playing surface every time it rains and shortens the acrylic surface life. Perimeter drainage — a French drain along the low side, or at minimum a graded swale directing water 10 feet clear of the pad — keeps the base dry season after season.